Along with increasing the efficiency of modern heating equipment, the complexity of the units increases and the requirements for its maintenance increase. Agree, it is extremely unpleasant if, after a year or two after installing the device, you find condensate in a gas boiler: what to do in this case, we will tell you below.
If urgent measures are not taken, then the equipment itself and the chimney will begin to collapse. At the same time, inside the house equipped with the heating system, the walls will become wet, red smudges will form, black mold will appear, the finish will become unusable.
Properly selected and correctly installed chimney will solve all the problems. Also, a steam trap will help to cope with the situation, which will significantly extend the life of the chimney system. From our article you will find out what condensate is, how to get rid of it and what a chimney should be like.
What is condensate?
Condensate is a liquid that settles on the walls of the chimney as a result of temperature changes. In modern gas equipment, the exhaust gases have a low temperature.
Causes of condensation:
- improperly insulated chimney;
- sharp temperature difference;
- unheated pipes;
- clogged smoke channel;
- low temperature of exhaust gases (ideally, the temperature should not be lower than 100 ° C);
- a very long chimney pipe, resulting in excessive cooling of the smoke;
- rough chimney walls (collect more water than smooth ones);
- structural defects;
- traction problems.
During the operation of the gas boiler, in addition to water, carbon dioxide and other chemical compounds (oxides) are also released.
Since modern boilers periodically turn off, the chimney walls are cooled from top to bottom. Condensate is formed when the temperature of the gases drops to 40-60 ° C
Under the influence of high temperature, the oxides react with water and aggressive acids are formed (nitric, hydrochloric, sulfuric, etc.). They settle on the surface of the equipment along with condensing vapors. Aggressive acidic environment leads to the rapid destruction of the chimney.
What is the danger of moisture formation:
- if the condensate freezes in the deflector or at the mouth of the pipe, the cross section of the chimney is blocked, as a result of the draft decreases, which can lead to the formation of reverse draft and combustion products will enter the house, causing poisoning of its residents;
- large amounts of water can extinguish the flame, which will result in carbon monoxide entering the room.
In addition, if moisture gets into the furnace of the boiler, its walls will collapse. As a result of the destruction, toxic combustion products will partially enter the house.
Condensation will destroy the chimney. If the problem persists, a complete pipe restoration will be required in the future.
Exhaust gas contains water in the form of steam. When the temperature of the gases drops, the steam becomes oversaturated and droplets form. In the case when the gases are hot, condensation occurs at the colder walls of the chimney, where drops of liquid settle.
Why does moisture appear in gas boilers?
In addition to condensate in the chimney of a gas boiler, moisture can also form in water pipes. The main reason lies in the temperature difference.
Also, the appearance of “dew” on pipelines is affected by:
- improper ventilation (not enough exhaust hood);
- high level of humidity in the room;
- incorrect operation of heating equipment.
The device of the gas boiler does not completely get rid of the condensate. However, it is in your power to reduce the rate of moisture formation and its amount.
Condensate control in atmospheric boiler
If an atmospheric wall-mounted or floor-mounted gas boiler is installed in the house, then the combustion products are heated to 170-200 ° C. Water is also present in the combustion gases. However, it does not condense, but turns into steam and is discharged through the smoke channel along with other smoke and volatile particles of soot.
When starting gas equipment after a long period of inactivity, a small amount of condensate is allowed to evaporate after the boiler warms up. In the cold season, the boiler works non-stop, so the appearance of liquid is unlikely
If condensation forms in the chimney, then the problem is in poor-quality thermal insulation of the chimney. Moreover, the formation of droplets of condensate on the smoke channel can occur both due to insufficient insulation and from excess.
In pipes made of stainless steel, the problem of the formation of condensate can be solved by installing a condensate neutralizer and by completing with an element of removal of condensation moisture deposited on the pipe surface.
When assembling ordinary metal chimneys and sandwich chimneys, it is imperative that the assembly and connection of the elements be followed, which provides for spontaneous removal of condensate outside the chimney.
“Dew” warning in a turbine boiler
Models with a closed burner are equipped with a coaxial chimney. It provides a slope of 3 ° outward, i.e. from the boiler, it provides a spontaneous drain of condensate to the street.
The internal channel of the coaxial system is constantly cooled by the air flow coming from outside, due to which the temperature difference during normal operation is minimal.
The standard length of the coaxial smoke exhaust system is 1.2 meters. If elongation is necessary, (mandatory indoors), the distance should not exceed 6 meters. There should be at least 0.6 m between the outlet of the outer part of the coaxial chimney and the nearest obstacle (wall, large tree, etc.).
If the boiler is equipped with a coaxial chimney, problems with the formation of condensate occur during the frosty period. They are solved by warming the part of the smoke channel located outside the house, by strengthening ventilation, or by starting the boiler at full capacity
When using a boiler with a coaxial chimney in the northern regions, it is advisable to insulate the outer part of the outlet pipe. In this way, condensation can be prevented in the chimney of the gas boiler. After all, the difference between the temperatures of the incoming air flow and the exhaust flue gases will be reduced.
You can temporarily provide the boiler with air flow from the room. Most turbocharged models of floor and wall gas boilers are designed for the possibility of separate systems of inflow and exhaust. You just need to find the plug of the hole to which the exhaust pipe should be connected, and slightly open it.
With an ajar plug for the exhaust duct, you can wait out frost. Then it must be covered tightly. Even in these cases, an increase in boiler power during the period of frost helps. In automated systems, a temporary reduction in the interval between the activation temperatures of the boiler and the boiler stopping set by the owners works well.
Feature of condensing boilers
The ideal solution is a condensing boiler, which is correctly balanced with the heating system, correctly configured and operates in the appropriate mode. In this case, the appearance of condensate is absolutely not harmful, because its energy is rationally used by the system itself.
The amount of gas saved directly depends on the amount of condensate formed.Condensation heat, which was formed during the operation of the equipment, is collected and redirected to the heating circuit. The efficiency of such a boiler is 98%.
Is condensation allowed to drain into the sewer?
During operation of the gas boiler, oxides are formed that react with water vapor. As a result, carbonic and sulfuric acids are formed, the average pH of which is 4. For comparison, the pH of beer is 4.5.
The acid solution is so weak that there are no restrictions on the discharge into public sewers. This rule applies if condensation has occurred on the pipe of a gas boiler operating in an apartment.
The only condition is that the condensate must be diluted with waste water 1 to 25. If the boiler power is more than 200 kW, it is necessary to install a condensate neutralizer. This requirement is indicated by the manufacturer in the equipment passport.
It is not possible to collect condensate into an autonomous sewer, which discharges effluents to a septic tank with anaerobic bacteria or to a deep cleaning station using anaerobes and aerobes. It will destroy the biological environment involved in the cleaning process.
Chimney requirements for gas boilers
Today, in the construction of chimneys for gas boilers, various materials are used, most of which are impractical. Workmanship also leaves much to be desired.
Chimney made of asbestos cement. In the past, such chimneys had no alternative. Their main advantage is low cost.
Disadvantages:
- installation is carried out exclusively on vertical pipe sections;
- large weight and length, which complicates the installation;
- joints are not tight;
- moisture is absorbed into the walls;
- flue gas temperature not higher than 300 ºС.
It is important to connect the boiler to the chimney correctly. A tee is used for this purpose.
If a tee is used in the chimney, then installation is carried out “by smoke”. In its absence "in condensate"
Be sure to have a steam trap and hatch for cleaning.
Brick chimneys. This material is not recommended for equipping systems with gas boilers. According to the requirements indicated in the collection of SNiP 41-01-2003, the flue ducts for gas processing equipment must be smooth and related in gas density to class P.
If the brick smoke channel is quite suitable for the gas density characteristics, then there can be no talk of the smoothness of the walls inside the pipe. Even if the seams of the brick pipe are perfectly sanded with a mortar flush with the brickwork, during operation the relief will still appear due to the difference in the density of the material and the binder.
The ideal solution would be to install a metal sleeve inside a brick channel or assemble it from ceramic modules. A brick pipe with a metal or ceramic insert inside can last without problems for more than 30 years.
Furanflex lining is suitable for the same purpose. This polymer sleeve is made of composite (plastic reinforced with high-strength fibers). It is resistant to acid condensate, has a low thermal conductivity. Permissible temperature of use is up to 200 ºС.
Ceramic smoke ducts. This material is durable and durable. The ceramic chimney is resistant to aggressive acids, easy to maintain and fireproof.
Ceramics can quickly heat up and cool for a long time. Installation of such a chimney requires the participation of specialists. The downside is the high cost.
Galvanized and steel. Under the influence of moisture, the steel rusts. The maximum shelf life of such pipes is up to three years. Galvanized chimneys, protected by a layer of zinc from rust, last five years or more.
If moisture does not penetrate the boiler, it accumulates in the lower part of the chimney (in the house), this leads to an unpleasant odor. At the same time, this is a vulnerable place where acid is collected, which over time “eats” this area
Stainless steel pipes. The perfect choice for arranging the smoke channel of a gas boiler. Its installation will cost several dozen times cheaper than the construction of a brick chimney. The walls are smooth, soot and tar will not settle on them, the gas density is quite high.
To assemble the chimney, you can purchase a set of single-layer modules or buy elements of a sandwich system. You can assemble such a design without much effort with your own hands. The main thing is to follow the direction when forming the connecting nodes.
Warming and chimney decoration improve the aesthetics of the building, which gives the house a more well-groomed appearance
Advantages of stainless steel chimneys:
- due to the round section and smooth surface provide good traction;
- tight;
- they quickly overcome the condensation threshold;
- easy to maintain;
- fireproof;
- durable.
Equally important is the quality of steel, weld, joints between the elements.
When sealing joints, great attention should be paid to sealant. Some grades “stone” and crack during operation
Often, the fact that repairing a chimney is much more expensive than competent installation at the stage of installing gas equipment is often not taken into account.
Chimney installation rules
The whole system must be insulated, waterproof and protected from aggressive materials.
The basic principles used during installation:
- collect the chimney should be "condensate";
- each joint is treated with a sealing compound;
- it is better to retreat from the vertical by a maximum of 30%;
- the length of inclined sections constructed at an angle of no more than 30º to the horizon, up to one meter;
- along the entire length of the channel, components of the same section are used.
It is recommended to install ready-made chimney sets, which are presented in specialized stores.
The placement of an acid-resistant sleeve and condensate collector makes it possible to delay the dismantling of the old chimney and saves a significant amount. However, be prepared for reduced traction
Recommended chimney system parameters for gas boilers:
- for the manufacture of the chimney, it is necessary to use corrosion-resistant steel type AISI 321;
- minimum thermal insulation - 50 mm;
- The system must include: a tee with a condensate collector, as well as a protective cone above the upper section of the chimney.
When choosing a chimney, you should pay attention to these characteristics.
Condensation Prevention
Forgetting moisture in the chimney forever will not work. The formation of condensate is inevitable, although during the continuous operation of the gas equipment, the “droplets” that have settled on startup will evaporate themselves and will no longer fall out while the unit is operating at full capacity.
To reduce the amount of moisture generated, reduce the circulation of the system when starting up the boiler. Let the boiler heat the coolant in the heat exchanger to at least 600C. Then you can increase the speed of the pump. Do not let the temperature drop below 300WITH
How to reduce the amount of condensate:
- to insulate the chimney channel;
- clean the system in a timely manner;
- use a steam trap.
If condensation builds up in a gas heating boiler, a container must be installed to collect excess fluid. The steam trap is a container made of stainless steel, which collects the moisture that has appeared.
Old chimneys are also recommended to be upgraded by installing a condensate trap in the bottom
The device is mounted under the outlet channel or pipe of the gas equipment. They also establish a permanent drainage to the sewer.
The problem of moisture formation in the chimney is better to prevent than to spend time and money later on to solve it.
The optimal solution for condensate removal will be to equip the pipe with an acid-resistant stainless steel channel, a diverter and an additional collector
Prevention of moisture:
- adhere to all standards during the construction phase of the building;
- when installing the chimney, clearly follow the project;
- regularly maintain the chimney using specialized chimney cleaners;
- modernization of existing pipes (insulation, insert inserts from stainless steel);
- monitor the draft power and clean the chimney in time.
Chimney insulation is carried out using mineral wool or fibrous insulation. To insulate a brick chimney, plaster is used, which is laid in seven layers.
Determination of the probability of condensation
Calculations can be carried out if condensate is formed as a result of a large emission of steam and overheating of the chimney walls, and the power of the working equipment is also known. The average heat release rate is 1 kW per 10 square meters. m
The formula is relevant for rooms with ceilings below 3 m:
MK = S * UMK / 10
MK - boiler power (kW);
S is the area of the building where the equipment is installed;
CMD is an indicator depending on the climatic zone.
Indicator for various climatic zones:
- south - 0.9;
- North - 2;
- middle latitudes - 1.2.
When operating a double-circuit boiler, the resulting MK should be multiplied by an additional factor (0.25).
The following video will familiarize you with information on how to protect the boiler from condensation:
Condensation in the chimney is inevitable. Since this cannot be avoided, we told you about how to reduce the quality of moisture and protect equipment from aggressive fluids.
It is recommended to strengthen the chimney with stainless plates, install a condensate collector and monitor the presence of draft. Do not forget about cleaning the chimney, as well as preventing the condition of its walls.
If you have a successful experience of “dealing” with condensate, share your secrets in the comments. Readers who have questions can ask their experts online.