Inveterate summer residents and adherents of summer suburban life are well aware of the problems associated with the lack of water supply. But water is constantly needed by plants for irrigation, animals, owners for hygienic and culinary purposes. How do you want to just open the tap and get it in the required volume, even in summer conditions. Do you agree?
We are ready to share with you all the possible ways according to which they arrange a summer water supply in the country. Here you will find reliable information about the selection of equipment and the construction of popular types of autonomous systems.
We offer a thorough analysis of the methods, valuable recommendations on the choice of source, laying of the onshore and underground pipelines. The basis for the information presented is normative documentation and advice from experienced professionals. The information is backed up by selection of photos and videos.
Distinctive features of summer water supply
The country watering system in practice turns out to be a vague and indefinite concept. For some, this is a pair of galvanized buckets and several hours a day spent on difficult “walks” to the well and back, for others it’s a long flexible hose that constantly clings and bends, for others it’s a complex pipe system leading from the well or pond to all corners of the garden.
We will consider the most optimal options, eliminating large physical loads during irrigation and minimizing financial costs during their construction.
Image Gallery
Photo from
Water supply for the organization of watering the site
Outdoor water supply lines
Water for fountains and country pools
Water supply to summer kitchens
Water supply for showers and country baths
The introduction of a water supply system in the country
Civilized conditions in the house
Bath for procedures
Of course, a seasonal water supply system can also have additional functions, for example, supplying a garage with water to wash the car, or providing an outdoor shower. However, they are possible only when a competent project has been drawn up and there are no complaints about laying a summer water supply system, otherwise, instead of convenient functionality, you will get many reasons for repair.
Do not forget that the summer modification differs from the winter one in some aspects of installation and maintenance:
- for laying pipes do not need deep trenches, but enough grooves with a depth of up to 0.7-0.8 m;
- during the warm period there is no need to warm the pipeline;
- for permanent systems, it is necessary to think over the drainage system (for collapsible communications, drainage occurs spontaneously during dismantling);
- temporary collapsible pipelines are connected in series, more serious, stationary - using a manifold.
The difference applies to the choice of pumping equipment. For example, to supply water to the garden from a well during the entire summer period, a submersible or surface pump is sufficient. A permanent system that operates year-round requires a powerful pumping station equipped with a water heater and storage tank.
The main purpose of the outdoor branch of the summer water supply is to water lawns, flower beds, beds, shrubs and trees; it operates temporarily and is used exclusively in the summer (for some regions from early spring to late autumn)
The choice of irrigation system also largely depends on the duration of the warm period. Suppose for the harsh north, where the summer lasts 3, or even 2 months, a collapsible scheme is quite enough.
And for the southern regions, where planting begins already in the early spring, it is better to build a solid, strong, reliable stationary water supply.
One of the options for supplying water to the garden plot is the Al-ko Jet 3000 surface pump (capacity - 3,100 l / h, power - 650 watts). Suitable for pumping clean water from a well or well.
Water source selection
The productivity, length of the structure and other operational capabilities of the irrigation system largely depend on the water source to which it will be connected.
Here is a list of options for watering:
- a well or a well (relevant both for new, recently developed sites, and for old, perennial possessions);
- natural water body (for example, a pond, originally located in the garden);
- centralized highway (necessary for water supply of modern cottage villages).
An excellent addition to the formation of the reserve will be the rainwater storage tank, the filling of which depends on the vagaries of the weather, and the VOC storage well, in which the treated wastewater separated from the insoluble sediment is accumulated.
Most often, in addition to the main source, there is a backup, for example, a large plastic tank located at a height of 1-1.5 m. If the electricity is suddenly turned off and the pump stops, watering is carried out from the tank.
A detailed installation diagram of a biological treatment station with a drainage well, from which, using a submersible pump and a system of pipes (hoses), it is possible to organize watering of lawns, a garden, garden crops
A simple, albeit costly, payment option is to connect to a central highway. The pipe leading to the place of irrigation cuts into the main pipe using a tee and a ball valve without shutting off, under pressure, since the preliminary installation of the valve allows you to drill a hole through it.
Watering from a natural source requires the installation of an additional filter system, because most budget pumps work only with clean water. A filter is also necessary for equipment submerged in a well or sand well.
Cleaner water is in the artesian well, but it requires a special deep-well submersible pump (popular brands are Dzhileks, Grundfos, Patriot, Belamos, Caliber).
Convenient plastic containers designed to collect rainwater from the roof replaced the old metal barrels. Built-in tap and connected pump make the irrigation process more comfortable
Storage tanks are different: metal and plastic, large and small, purchased and home-made. If the site is small and the tank is voluminous, there is enough fluid for several irrigation.
The pipeline, which operates in the summer, can be attached to any of the sources listed, but with minor reservations. Suppose a collapsible design is suitable for working with a plastic container, and it is better to build a permanent system to connect to the well.
Image Gallery
Photo from
The easiest option is an open pond.
Abyssinian well for water supply
Water intake for a well system
Well on a seasonal dacha
Types of water pipes for irrigation
Before designing a summer water supply system for irrigation, you should find out which scheme is more suitable: collapsible or stationary. These two systems have the same purpose, but differ in the nuances of mounting / dismounting (collapsible) and design features.
Collapsible scheme: pros and cons
The main distinguishing feature of the collapsible design is the need for annual installation and dismantling. In spring, parts must be assembled, in autumn - disassemble, then all pipes, tubes, hoses and fittings should be cleaned, washed, dried and put in a dry room.
The assembly is made of plastic pipes connected by fittings, flexible hoses and tips for easy watering; head adjustment is made using taps
A temporary collapsible water supply system is assembled and disassembled according to the principle of a children's designer: it is necessary to take parts that are suitable in size and connect them into a structure that ensures the movement of water from the source to the irrigation site.
The ease of installation and budget cost have made the system popular: a lot of ready-made offers from various manufacturers have appeared in supermarkets.
Elements of the irrigation system are most often sold separately, but the sales assistant can select the necessary details for the finished project - from pipes and fittings to the pump. There are also full-fledged kits designed for drip irrigation, a technology quite new, but already having regular fans.
The device of the drip irrigation system in the greenhouse: the source of water is a storage metal container (barrel) installed at a height of 1 m, flexible hoses are connected by a crane as needed
Drip irrigation occurs due to the regulated water supply through flexible hoses with small holes located near the root system of plants. The advantage is the metered supply and water saving, in which the plants receive the required amount of moisture.
The advantages of any collapsible type are:
- quick assembly and disassembly;
- assembly that does not require special knowledge;
- operational repair;
- budget cost.
There is a drawback - the need for assembly / disassembly. Many do not like finding hoses on the surface. They interfere with the movement and spoil the appearance of the site, but if you think about the neat, disguised arrangement of flexible hoses (along paths, along the edges of lawns or beds), the problem will be solved.
A photo selection will introduce the specifics of assembling an independent system of HDPE pipes:
Image Gallery
Photo from
Spout with tap for water collection
Loy system coils
Drinking category is a priority
Parts for connecting pipes to the system
Collapsible irrigation systems
Application in the repair of water supply lines
Open laying
Underground installation of water branches
Permanent system arrangement
For the installation of a permanent summer water supply, trenches are dug, this reminds him of communications operating throughout the year.
Unlike the winter system, pipes of the summer modification are not tied to the level of freezing and therefore are located at a shallow depth of about half a meter, a maximum of 0.8 m. The depth depends on the installation location: the more actively the land is used above the pipes, the deeper they are lie.
Structural elements consist of plastic, metal-plastic, rubber or silicone; regardless of the material, the walls of the pipes and connecting elements must be thick and strong enough to withstand the pressure of water and soil
A mandatory part is a drain valve, which is necessary for the process of draining water at the end of the season. It is installed at a convenient point laid down under the slope of the pipeline so that water can flow out on its own. The procedure is carried out before the onset of cold weather, without waiting for a negative temperature, otherwise the water will freeze right in the pipes and damage them.
In addition to the pipeline located underground, water-folding cranes are brought out. They are mounted at points located in close proximity to the irrigation zones - in the garden, in the garden, near flower beds and lawns, as well as in the garage.
Flexible hoses with convenient spray nozzles are attached to the taps for more efficient irrigation or spraying of plants.
Installation of a water-folding crane on a vertically located plastic pipe cut into an underground highway - a structure suitable for both open-air plantings and greenhouses
The advantages of a permanent water supply:
- communications do not interfere with the movement of people and transport;
- the pipes are protected by a layer of soil from damage caused by external influences;
- in the spring it is not necessary to carry out installation, and at the end of the season - dismantle;
- preparation for conservation is simple - drain water from pipes.
The downside is the high cost and additional excavation work. If depressurization occurs, it is not possible to quickly identify the emergency site.
The assembly of a system of rigid polymer pipes has its own characteristics:
Image Gallery
Photo from
The device system for watering the site
Shutoff valves of a water supply system
Water Automation Equipment
Open construction option
Arrangement of a water intake point on the street
Grounding water lines
Storage tank for water reserve in the country
Places for laying a summer cottage system
A brief overview of materials and necessary devices
The summer water supply system consists of the following elements:
- pipes;
- cranes
- fitting;
- pump equipment;
- filters.
For comparison, during the construction of the winter, pressure control devices (pressure accumulator, pressure gauge, pressure switch), automatic protection, and a water heater are required.
There are many options for automated systems that allow you to regulate and control drip or greenhouse irrigation.
Scheme of automatic irrigation in the greenhouse, assembled from flexible hoses. Pumping equipment that supplies water from the storage tank is powered by solar energy
Conventional water pipes made of plastic, polypropylene or polyethylene with a diameter of 20 mm to 25 mm are more suitable for deepening into the ground. Polypropylene products with reinforced layers, for example, German Banninger pipes for hot water supply, which have a characteristic green color, are especially durable.
However, for small, low-branched schemes, white medium-strength PVC pipes are suitable.
Hoses should not be placed in the ground, but used on the surface. If you still decide to build a permanent water supply exclusively from hoses, then choose products with thick walls reinforced with nylon fibers. Their service life is usually not less than 15 years.
Fittings (tees, couplings, clamps, plugs) should fit in diameter, ideally in material. Prefabricated structures usually come with the necessary number of connecting and fixing elements to ensure tightness
The only volatile element in the system is a surface or submersible pump. It should be chosen based on their data on the source of water and the characteristics of the equipment itself. For example, the best option for a pond is a drainage pump, for a well - a deep pump, and for a well, a fairly inexpensive submersible model such as "Kid" or "Trickle" is enough.
Assembly instructions for temporary water supply
For the installation of seasonal “temporary shelters”, a set of pipes and fittings that are suitable in diameter and a pump for forced water supply will be required. To correctly calculate the amount of consumables, make a drawing in the form of a sketch on which you need to specify the length of all highways and the junction.
Scheme of drip irrigation, providing irrigation of greenhouses, beds in open ground and garden plants. The object for the water supply is the storage tank installed on the supports, so the use of a pump is possible, but not necessary
To equip drip irrigation, it is enough to purchase a ready-made kit, equipped with instructions.
To assemble according to your own scheme, proceed according to the following plan:
- lay out the pipes according to the drawing, determine the location of the water points;
- if there are enough elements, connect them with fittings;
- attach additional parts (irrigation nozzles);
- connect the system to a pre-installed pump;
- test the running water.
With the pump turned on, check the pressure at all points and the tightness of the communications.To prevent hoses and pipes from getting underfoot, try to think through a scheme so that they do not intersect places of active traffic and the road for traffic.
If you constantly use surface water supply, use various ideas for the convenience of laying it. For example, during the construction of a garden path, lay transverse pipes with a diameter of 50-100 mm in several places under its base in several places. For the winter they can be closed with caps, and in the summer they will serve as a kind of tunnels for the installation of water pipes and hoses.
And in this material you can read more similarly about choosing flexible watering hoses.
Installation of a stationary system with a pump
The main part of the permanent irrigation water supply system is placed in the ground, so the selection of parts and installation should be carried out with special care. We offer a universal trunking scheme suitable for simple and branched networks.
#1. Designing the landscape
Planning, taking into account all the nuances of the subsequent assembly, is half the success, so even before buying the necessary materials, draw up a diagram with the designation of important objects (water source, irrigation points, all buildings, paths, beds and plantings).
Using a tape measure, measure the required lengths of the section and calculate the length of the pipes and the number of connecting parts.
An approximate scheme of the summer water supply: 1 - storage tanks for rainwater; 2 - storage tank in the garden; 3 - a raised tank for drip irrigation in the greenhouse; I - II - tie-in nodes to the main highway
Consider how to better position the trenches relative to paths, buildings, watering zones. Count on a shallow depth - 0.3-0.4 m, but for potentially dangerous places it needs to be increased to 0.7-0.8 m.
Do not forget about the insert of the drain tap - it is traditionally mounted next to the water intake, respectively, the inclination of the pipes should also occur in the direction of the source.
The more taps, the less often the flexible hose will have to be moved. Mentally break the garden (flower garden, lawn, garden) into small areas and plan the installation of hydrants with a device for attaching a hose or a sprayer.
An approximate list of materials and tools that will be required to assemble the irrigation system:
- pipes with a set of tees, elbows and fittings;
- flexible hoses;
- cutter and soldering iron for plastic pipes (hacksaw for metal - for metal);
- ball valve ½;
- pump for installation in a well.
The availability of various parts and their quantity depends on the requirements of a particular project.
# 2 Earthwork - device of trenches
To dig a shallow trench, a single tool is required - a shovel. Buckets or a wheelbarrow for the removal of soil are not needed, since it is necessary for backfilling.
The complexity of the event depends entirely on the quality and composition of the soil and plant layer. It is easy to dig a soil with a high sand content, even with numerous plant roots, removing ORS with the inclusion of clay components is much more difficult.
Earthwork at the summer cottage: preparation of trenches for the installation of water pipes. Each trench turn - plus one compression elbow for connecting pipe sections
On the way to laying communications, there may be buildings that have to be circumvented around the perimeter (for example, a barn or a pool). Small cottage objects can be overcome by slightly deepening the trench. Suppose communications laid under a flowerbed at a depth of 0.7 m will not interfere with digging and caring for plants.
It should be remembered that each turn of the pipeline will reduce the efficiency of the system and increase the load on the pumping equipment. Therefore, when developing a scheme for laying a pipeline system, it is necessary to choose paths with a minimum number of turns, if possible, with their complete absence.
# 3 Pipeline Assembly Options
Previously, when metal pipes were used, it was necessary to deal with steel parts, the cutting and assembly of which was more time-consuming. Now they use plastic pipes, which are interconnected in two ways - by welding or fittings.
The first technology is a bit more complicated, but the result is more reliable. Before welding, it is necessary to prepare polypropylene pipes - cut into fragments of the required length. For the central highway, a pipe with a diameter of 20-25 mm is suitable, for branches - 10-20 mm, so cutting can be done with scissors or a roller cutter.
For welding, you will need a special welding machine - a soldering iron with a heater and a compact control unit. As a result of heating, the pipes are soldered with fittings, forming a monolithic tight design.
The process of joining a polypropylene pipe and a connecting corner by welding. For reliability, it is necessary to withstand all stages: heating to the desired temperature, fixing and cooling
Before starting welding work, carefully read the instructions and remember the rules for using the welding machine. For example, do not cool pipes with cold water or compressed air.
Having assembled the pipe structure, you do not need to backfill - first you connect to the pumping equipment and check the operation.
#4. Pump connection and testing
As a rule, at the time of construction of the irrigation system, a pump is already installed. If not, you must select a model that is suitable for a particular source (for example, a well) and install it according to the instructions.
The submersible pump is lowered into the water and fixed at a certain distance from the bottom, the surface is installed near the well, covering it with a protective casing.
Watering “directly”: a flexible hose with a watering can is connected to a submersible pump that pumps water from a well. The scheme is also relevant for a pond or storage tank.
The crucial moment is testing. After connecting all the elements into a single system, turn on the pump and check the tightness of the water supply. Pay attention to the quality of irrigation - is there enough pressure at the most distant points. If everything suits you, you can backfill by tamping the soil slightly and start using the summer system.
Maintenance mainly relates to the operation of the pump. The pipeline only needs preparation for winter conservation. To do this, open the tap and drain the water.
Useful and informative videos to understand how the summer irrigation system looks and learn more about its installation.
Variant of arrangement of a country water supply system with connection to a well:
In the next video, we will talk about how to build a plastic water pipe yourself:
A detailed overview of the elements for an irrigation system:
As you can see, the device of a summer water supply for irrigation is affordable for any summer resident who knows how to handle a pump. If you have any questions or difficulties, we recommend contacting specialists who are engaged in landscape design or equipping summer cottages with water supply systems.
Concerned about arranging a summer cottage? Or maybe it was already possible to independently carry out its installation and you have something to share with our readers? Please share your experience, write your comments, ask questions at the bottom of the article.