Stable watering is the key to obtaining a plentiful harvest from garden beds. If on rainy days the weather takes care of the plants, then in the hot months it is up to the gardeners to decide, using buckets and watering cans for this. The use of pumping equipment helps to facilitate the work.
The market offers various pumps for watering the garden and it is difficult to get a suitable model, right? We will help you navigate the range of equipment, talk about the features of different modifications and provide a step-by-step selection algorithm based on an analysis of the characteristics of the units.
In addition, we will designate trademarks and brands whose products are in demand and trust among summer residents.
Source selection for water intake
The selection and purchase of a suitable model of garden pump for irrigation largely depends on what water is supposed to be pumped and where it is planned to take from.
Plants cannot develop normally without enough life-giving moisture. But only well-settled warm water is suitable for watering green spaces.
Rain water is the most affordable option for life-giving moisture, which has a neutral acid-base balance and contains a minimum of chemical impurities that are dangerous to plants
Zealous owners collect rainwater in barrels and large tanks located on the site under the drains. If necessary, it remains only to get it, scooping it with a bucket or pumping it out from the barrel with a pump for irrigation.
Quite often, if a well or a well is present at the site, then water for irrigation is taken from them. But the “cold shower” can cause irreparable damage to the delicate roots of plants: they can begin to rot.
For this reason, the water pumped out of the hydraulic structure is first poured into a tank, allowing it to warm up under sunlight, and only after that it is used for irrigation.
The third, and perhaps the most successful version of the source, from where it is convenient to take water for irrigation - a nearby natural reservoir or an artificial pond constructed on its own.
Using water from a home pond for watering plants, you solve two problems at once: give life-giving moisture to green “pets” and perform preventive cleaning of the water structure
In all of the above sources, water is very different in terms of degree of contamination. Therefore, for each of them separate types of pumping equipment have been developed.
Types of pumps for pumping water
For irrigation of garden crops, two types of pumps are used. Depending on the method of water intake and placement of the unit body relative to the source, they are surface and submersible.
Option # 1 - barrel for pumping tanks
Such devices are designed specifically for pumping water from small tanks, the depth of which does not exceed 1.2 m.
Among the pumping equipment on the market, such units are considered the easiest to use and maintain.
The main advantage of pumps for the production of irrigation from a barrel is compactness and mobility. The weight of the unit averages 3-4 kg.
Taking it by the handle, it is convenient to carry it around the site and alternately install it on containers located under the catchments. In addition, barrel pumps are known for low noise.
To pump out the irrigation fluid, the barrel pump with the bracket is simply fixed on the edge of the tank and connected to the mains
The use of barrel aggregates is also convenient because the water used for irrigation can be pre-diluted with fertilizers to feed cultivated plants.
Most models are equipped with a pressure regulator. With its help it is convenient to set the pressure necessary for work. Filters for holding large particles are built into the pumps for tanks.
But as noted by owners who have already tested household models of this type, built-in filters do not always cope with the task. As a result, even expensive systems quickly become clogged and fail.
The easiest way to solve this problem is by arranging an additional home-made filter in the form of a cut from gauze or net tulle folded in 2-3 layers.
The pump is simply placed on a canvas suspended in the form of a hammock so that the mesh layer between the suction device and the water does not allow debris to leak out.
Rust and sludge can be prevented from entering the system by placing the pump inside the tank so that it does not reach the bottom of the tank by 5 cm.
Image Gallery
Photo from
Pumps for pumping water from tanks can be used not only for watering the garden, but also for transporting water to other containers
The rainwater pump is installed at the bottom of the tank, located under a drain funnel or riser
Preparing the pump for irrigation, pumping water or cleaning the site consists in attaching the hose to the telescopic rod, which allows you to set a convenient height
Pumps for using rainwater include hoses of various diameters and nozzles, a sprinkler can be connected to the unit
To select the optimal operating mode of operation, there is a switch, to extend the life there is protection against dry running
The mechanical part of the pump is protected from damage by an integrated filter. Larger parts prevent the support ring
Automatic switching on and similar switching off is provided by a float device that responds to the maximum allowable decrease in water level
The telescopic rod, to which the hose is connected, is assembled to give a compact shape, spilling it serves as a carrying handle
Pumping equipment installed at the bottom of the tank
Preparing the pump for watering
Connection to a sprinkler pump
Mode switch
Filter and support ring for the bottom
Automatic float switch
Assembly pump for storage
Option # 2 - surface for shallow ponds
When planning to use an artificial pond or well as the main source of water intake, it is worth considering models of surface pumps.
They are placed in the immediate vicinity of the source, and water is taken by immersion in the construction of the suction hose.
Outdoor devices are able to pump water from a depth of 8 m and issue a stream to a level of about 30-50 m. Thanks to this pressure, from one point you can water several rows of beds at once.
To start the pump for irrigation from a reservoir, you only need to install the device on a flat surface, attach a suction hose and a discharge pipe to it, and then connect it to the power supply
A metal pipe is used as the outlet pipe for most surface models. The rubber hose is not suitable for this purpose because rarefied air is created inside it at the time of pumping the liquid.
As a result: the elastic walls begin to shrink, preventing the water flow from moving normally towards the exit.
The only drawback of pumps for irrigation from shallow reservoirs is the vibration and the formation of noise during operation.
You can get rid of the loud “growl” by placing the unit in the outbuilding, or by placing the unit body on a rubberized rug or stand.
Image Gallery
Photo from
Garden pump with two outlets
Built-in filters to protect the pump
Resistant rubber mounts
Proper conservation of the surface pump
Option # 3 - Submersible for Contaminated Ponds
Submersible pumps are rarely used for gardening purposes. The working part of this type of device is immersed directly in the source, buried below the water level. The pumped liquid under pressure is discharged to the surface through rubber pipes.
Submersible units, in contrast to outdoor models, are able to cover long distances to garden beds without losing pressure, which is especially valuable when the source is located remotely
Depending on the type of model, submersible pumps are able to pump water from a depth of 80 m. This parameter is relevant when used as a source of water for irrigation of a drilled well.
According to the method of water supply, submersible irrigation pumps are presented in two versions:
- Vibrating. They work due to the movement located inside the membrane. It causes pressure drops, under the influence of which water is first sucked in and then pushed out. Vibration devices are low in price, but are afraid of clogging with silt.
- Centrifugal. Raise water to the surface by rotating the blades and wheels. They "grind" the water with such force that minor pollution is not afraid of them. But such units are much higher than vibrational ones.
The outer shell of submersible pumps can be made of stainless metal or plastic. Each of these materials is designed for constant contact with a constant contact with the working medium.
If necessary, use a pond as a source of water intake, the water in which is not very clean, the preference should be attributed to drainage models.
Such aggregates are ways to “process” lightly and heavily contaminated water, which contains various kinds of impurities with a diameter of 5-10 mm.
For irrigation of garden beds, drainage devices equipped with shredders, designed to pump out cold drains, are quite suitable
The chopper located just above the suction device will crush the leaves, sludge and other debris that have fallen into the device with the smallest particles during pumping.
Thanks to this, irrigation water will be additionally enriched with organic fertilizers, which will only positively affect the yield of cultivated crops.
A significant drawback of the drainage units used as pumps for irrigation from the pond is the low pressure in the system. So you can water the garden with their help only by gravity.
If you plan to use a nozzle or a divider, then the water may not go at all. You can get out of this situation by completing the work in stages.
First, with the help of a drainer, liquid is pumped into the storage tank. And then, after it has settled and heavy sediments have settled, the garden is watered using a surface and submersible garden pump.
Option # 4 - automatic for drip irrigation
Especially popular are automatic pumps equipped with timers. They greatly facilitate the task for owners who do not have the opportunity to spend precious time and excess moisture on watering for hours.
Drip irrigation pumps are equipped with pressure switches and accumulators. Management in such systems can be either manual or automatic.
The owner’s task is to set the minimum pressure level at which water will flow out of the outlet pipe in a thin stream
Although such equipment is not cheap, but over time the costs fully pay for themselves, allowing more rational use of hundreds of cubic meters of moisture supplied during the season. Yes, and the owner freed up a lot of time that would have previously been spent on watering.
Aggregate selection criteria
When choosing pumping equipment, it is necessary to determine the following factors for yourself:
- Distance from the source of water intake to garden beds.
- Height difference from the installation site of pumping equipment to the extreme point of the garden.
- Plot sizereserved for crops that need frequent watering.
- Type of watering (radical, drip, sprinkling).
- Frequency of use pumping equipment.
For drip irrigation, it is enough to install low-power equipment. When planning to irrigate crops through sprinkling, you should give preference to systems that can easily withstand great pressure.
When purchasing a model, you should pay attention to how much tank capacity it is designed for and how much it can pump water in one hour
The most reliable are units with two-stage mechanisms. Such powerful aggregates are chosen by the owners of large areas, in which a large area is allocated for garden beds, a flower garden and a garden in need of watering.
No. 1 - calculation of device performance
To calculate the required performance of the purchased pumping equipment, averaged indicators are usually taken.
Depending on climatic conditions and soil conditions according to the current SNiPu for irrigation of beds with an area of 1 square. m is required from 3 to 6 liters per day.
Therefore, for a garden area of 200 square meters. m daily rate will be: 200x6 = 1200 liters.
To meet the needs in this case, you will have to purchase an aggregate with a capacity of 1.5-2 cubic liters per hour
The maximum capacity of barrel units is 4000 l / h. Choosing among low-power devices designed for pumping liquid from storage tanks, it is worth taking a closer look at models with a capacity of 2000 l / h.
The price of such devices starts from 2.5 thousand rubles.
When arranging drip irrigation, the most reliable type of pump is centrifugal. After all, only he is capable of pumping large portions of water under high pressure without damage to the motor overheating for a whole day.
When choosing among drainage models, keep in mind that such units have a capacity of 83 to 250 l / min with a water supply of 5 m to 12 m.
When using water for irrigation from especially polluted water bodies, the impurity diameter of which is 15-55 mm, it is worth choosing units with a capacity of 37 to 450 l / min. They are able to provide a feed to a height of 5-22 m.
No. 2 - recommended pressure of a stream
Pump pressure means mechanical operation of the unit, as a result of which the pressure of the liquid rises and it is pumped. In this case, part of the drive energy is converted into the kinetic energy of the liquid during pumping.
The head created by the device and the flow rate of the pumped liquid directly depend on each other, in graphical form this dependence is displayed in the form of a pump characteristic
The higher the value of the generated head, the greater the distance can be maintained between the pump and the source of water intake. When calculating power, also take into account that the ratio of vertical and horizontal lengths is 1: 4.
At the same time, when it comes to watering, then too much pressure is more likely to be troubles than good. After all, the exile pressure can not only damage the dividers, tearing them off the hose, but also harm the green spaces.
No. 3 - the presence of an automation system
Automation significantly increases the cost of pumping equipment. But it plays a significant role, preventing overheating of the "heart" of the unit - the motor.
The float mechanism is triggered by the action of a steel ball placed inside the box, which closes the contacts when the water level changes
A float switch protects the appliance's motor when the set minimum water level is reached. This prevents the unit from “dry running”, thereby minimizing the risk of breakdowns.
Having chosen a unit equipped with a float switch, during operation you will not need to control how empty the barrel is.
You only need to flush the float switch once a season under water pressure to prevent the box body from sticking to the outlet pipe.
No. 4 - location of the suction valve
The suction valve can be located above the engine compartment in the upper part of the device, or on the bottom of the housing.
The presence of a filter on the suction valve of the device will allow to delay debris falling with water, thereby extending the life of the unit
More practical models, the water intake which is located in the upper part of the body. This design solution reduces the likelihood of siltation and penetration into the chamber of the bottom sediment and particles of sand.
Using watering submersible units whose suction valves are located in the bottom of the housing, use special supplies.
By placing the pump on a stand, you can partially protect the working chamber from the ingress of fibrous inclusions, rocky sand suspension and large debris.
The pumps are usually supplied with adapters that allow you to connect flexible hoses and rigid pipes with a diameter of 1ʺ and 1 1/4ʺ. In budget models, most likely, the watering hose and spray nozzle will have to be purchased additionally.
Overview of pumping equipment manufacturers
High demand for pumping equipment for domestic use stimulates manufacturers. Today, foreign and domestic manufacturers offer a wide range of equipment in different price categories.
Imported global brands
Among foreign manufacturers that have proven themselves in the pumping equipment market, it is worth highlighting:
- HAMMER. German leader in the production of first-class pumping equipment. A wide range of products, unique technical solutions and the highest reliability - all this combines the products manufactured under this brand.
- "PATRIOT". One of the oldest American brands. The quality of the products manufactured by this company has been tested by generations. Reliable and convenient chainsaws in work are more known to the domestic buyer under this brand. But pumping equipment is not inferior to them at all.
- "Calpeda." Recognized world champion. The Italian company is famous for its good technical traditions. All equipment is manufactured using high-precision equipment.
- QUATTRO ELEMENTI. Another well-known Italian brand representing high-quality equipment. The company, founded by like-minded engineers, focuses on the reliability and maintainability of products.
Barrel models for watering the garden of these brands can be purchased at a price of 5.5 thousand rubles. More powerful surface and submersible units will cost 6 thousand and more. A drainage installation of medium power - within 9 thousand rubles.
Choosing products of famous brands, even in the event of a breakdown, it will be much easier to find spare parts for them, and even masters are more willing to accept them for repairs
Among the companies that are still only building up their potential, but have already earned a positive reputation among a wide range of consumers, it is also worth highlighting “Makita"And"Gardena».
Domestic trademarks
Popular brands of pumping equipment of domestic manufacturer:
- "Vortex". Leading Russian manufacturer. The main advantage of the products is ease of use, quiet operation and minimal hydraulic losses during pumping.
- Gilex. The Russian company produces reliable pumps that can be used both for pumping clean and slightly contaminated water for irrigation.
- "Gardener". Products manufactured under this brand successfully combine an affordable price with decent quality.Compact centrifugal devices easily handle contaminated water.
The price of centrifugal submersible pumps of these brands starts at 4 thousand rubles. Medium capacity drainage units cost from 5 thousand and more.
Budget models of domestic production "Trickle" and "Kid" are also very popular. The price of products ranges from 1.5-2 thousand rubles.
But it is worth noting that they are very sensitive to voltage fluctuations in the mains. To work in our conditions, it is better to choose centrifugal models for which no such sin has been noticed.
Recommendations for choosing an electric pump for irrigation:
Video review of the Karcher barrel pump application:
Equipment for pumping out a polluted pond:
And finally, I want to note that, regardless of the chosen model, equipment deficiencies are most often manifested due to improper handling.
If the device is designed to pump clean water, then do not lower it into a rain tank. Fallen leaves and sand will quickly clog the filters and disable the device. And it is not the manufacturer who is to blame for this, but only the inefficient owner.
Have experience using pumping equipment for watering garden beds? Please share information with our readers, tell us which pump you use. You can leave comments in the form below.