It happens that you take a hot bath or shower, steam up, relax - it's time to put yourself in order. You approach a mirror - and it is completely foggy, and even a towel cannot drain it. Or in the toilet for a long time there is a smell from the previous visitor or an obsessive air freshener. Familiar situations? Solving such problems will help the connection of an exhaust fan in the bathroom and toilet, common or two separate.
It is not worth neglecting the quality of the ventilation of the bathroom, because this is a matter of not only convenience, but also safety. Over time, mold and fungus are created along the bathroom, in the corners and in the seams between the tiles, which are dangerous to human health. It is often possible to completely remove them only during overhaul, so the acquisition and installation of an exhaust fan pays off with interest, preventing similar problems.
In this article we will tell you how to organize a system of forced ventilation of a bathroom, what to look for when buying equipment, how to install and connect everything yourself. We will consider options for connection schemes suitable for different models of fans and conditions of use, as well as give some useful tips on ventilation in the bathroom and toilet.
Choosing a fan and starting method
There are many models of exhaust fans on the market, including for the bathroom. They differ not only in size and appearance. There are a number of characteristics that should be considered when choosing and buying.
Fans for the bathroom are overhead and duct, with a solid front panel or grille, different colors and designs
The first thing that determines the connection diagram of the fan for extracting air from the bathroom is the way to start it.
Depending on the model, there are such options:
- Turning on the fan case with a button or cord - they are the easiest way to connect, but it’s not very convenient to reach the ceiling each time.
- Start by a separate switch or in parallel with the lighting. The fan itself also has only 2 wires, but the possible connection schemes are more complex and diverse. Including, with an external timer or hygrometer, motion sensor or door opening.
- Management through the built-in timer or hygrometer. Such models are connected by a three-wire wire.
- Remote control through the remote. These models combine the ease of connecting the first option and maximum ease of use, but also cost more than anyone.
In addition, not every exhaust fan is suitable for the bathroom. The fact is that this is electrical equipment, and for operation in high humidity conditions the protection class must be at least IP45, which is confirmed in the documents.
At the same time, each digit of the marking should be considered separately, that is, IP62 protection is not suitable, since the second digit indicates resistance to moisture, it should be at least 5.
In practice, protection is implemented in the form of insulated connection contacts, a hidden or moisture-proof control board, and a sealed motor housing.
Even fans with high moisture protection characteristics are not recommended to be placed so that water can get on them.
You should also determine the type of device design. Axial models are cheaper, but more noisy, as the air passes directly through them. Centrifugal fans form vortex flows that push air in a circle - it is much quieter.In addition, for a private house, you can choose which are installed inside the ventilation duct, and not at the exit from it.
Another critical parameter is the power and performance of the fan. For this, the volume of the room must be multiplied by 6 - 8, depending on the number of residents. The resulting figure is the minimum required volume of air exchange per hour.
Too weak a fan will not do its job well, it will have to be left on for a long time. Too powerful will not only add strong drafts, but can also provoke a reverse air flow from the general ventilation shaft, with all the neighboring odors.
Also pay attention to the diameter of the fan. If it does not correspond to the diameter of the existing ventilation hole, for installation additionally you will need a pipe and construction foam or a perforator, as well as much more effort.
The comfort of use is significantly affected by the noise of the equipment. Quiet models produce no more than 25-30 dB, less successful solutions - about 50 dB, and sometimes more.
The non-return valve will protect you from smells and moisture from the neighboring bathroom when the fan is off. It also partially protects the device from dust in the mine.
In addition to the above parameters, pay attention to whether the fan is equipped with a check valve, a ventilation function, a mode switch, a display with temperature and humidity indicators. Design decisions include original or replaceable protective panels, sometimes with backlighting.
Fan wiring diagrams
The most critical part of the installation of the ventilation system is the connection of electrical wiring. The correctness, efficiency and safety of the system, as well as the convenience of its use, depend on this. It is not uncommon that no one uses the installed fan in the bathroom just because it is inconvenient to turn it on or off.
Various connection schemes, as well as built-in and external devices allow you to automate fan control, or minimize the cost of installing it.
Devices with a switch on the case
An inexpensive and reliable option is to install a fan with a built-in switch. It can be connected to a power outlet or directly to a wire that supplies electricity to the apartment, whichever is closer.
In the same way, the most expensive models that are controlled by the remote control are connected. They also have a shutdown button on the case - emergency.
However, before you connect the fan directly to a wall outlet, think about whether you will reach the button or lace on the unit body each time? After all, you need to install it under the ceiling, where steam accumulates. Of course, the lace can be lengthened - but it is not aesthetically pleasing, and it is not always convenient.
There are models that were originally equipped with a plug for plugging into a power outlet. They help out if the need for forced ventilation is identified after finishing
The advantages of such a connection include ventilation control from inside the bathroom - after all, according to the PUE, any other switches and controls for electrical appliances should be located outside, in the corridor.
Connect the fan to the lighting
The simplest and most budgetary option for arranging forced ventilation of the bathroom is to connect the fan to the nearest light bulb, spending a minimum of wires and effort. In this case, the hood will work exactly as long as the light is on.
When connecting an exhaust fan in a bathroom or toilet according to this scheme, it is worth insulating the connection points of the wires well
Installing a fan with three wires is a bit more complicated. Such an assembly requires constant power to the board, so both phase and zero are drawn directly from the box to it.
The switch opens the additional phase wire that controls the timer. All connections are described in more detail in the diagrams below.
There are already 3 wires in the junction box: electricity supply from the shield (Gr. Osv), lighting supply in the bathroom (Light) and to the switch connected to the phase conductors of the first two
Of the three cores of the fan wire, one closes directly to the phase coming from the shield - it will ensure the constant operation of the control board
The core of zero is connected to the remaining zeros, and the third is connected to the wire coming from the switch - together with the phase that feeds the lighting
Connection through the box is safer, since all connections are outside the bathroom, but have the same operational disadvantages as the connection to the bulb. On the one hand, you will never forget to turn on the hood, you will need few wires, and you can hide them even after facing the walls - to the ceiling.
On the other hand, few people will like the draft and noise during bathing, and working hours from light for effective ventilation may not be enough. As a result, you have to leave the lighting on after leaving the bathroom or toilet, and this is an additional energy consumption.
The presence of a built-in timer in the exhaust fan eliminates these shortcomings: in the bath mode, it will turn on only after turning off the light and work for a specified time, and in the toilet it will start along with the lighting.
Connection via switch
This connection scheme is the most universal, reliable and widespread. Using it, you can connect any fan model and control it manually, regardless of lighting.
Connecting a fan with a timer is carried out almost in the same way as we described in the previous paragraph about the connections in the junction box. The fundamental difference is that the phase wire of the fan does not close together with the lighting phase, but separately - to the individual wires of the two-gang switch.
The wiring diagram for ventilation and lighting in the bathroom as a whole looks like this. The phase wires are marked in red, yellow and orange, blue - zero, light green - ground, if provided in the fan
To connect simple models in this way without a built-in timer, it is enough to bring the zero wire from the junction box directly to the fan, and the phase from the switch. If a single-key light switch is already installed, it is replaced with a two-key, and the wire from it to the box is replaced with a three-wire one. To the new core and connect the phase wire to power the fan.
Such a scheme can flounder most often for one reason: phase and zero are mixed up.
Alternatively, the connections can be made directly in the in-depth socket box - this will not affect the operation of the circuit in any way
If in the bathroom when the light is off, the diode lamps flash and the electronically controlled fan behaves in a strange way, it makes sense to open the junction box and double-check the presence of phase on the wire leading to the switch.
Read more about how to connect a fan to a switch.
The inclusion of an external sensor in the circuit
In any of the above schemes, you can include an additional humidity sensor, air pollution, a timer (if there are no built-in sensors), a motion or door sensor.
The most effective ventilation will be in the bathroom, controlled by a humidity sensor, and in the toilet - a timer or air pollution sensor.
Additional sensors are connected to the phase wire - the same one that comes from the switch, in a single line. Sometimes you need a connection and zero to the device
It is worth noting that external sensors, as a rule, are much less durable and reliable in a bathroom than built-in fans.
Fan mounting procedure
As in any construction work, the ventilation system must first be designed. It is better to do this even at the very beginning of the repair of the bathroom, in order to be able to hide all communications in the walls and under the ceiling.
If we are talking about a bathroom in an apartment where there is already a hole in the wall into a common ventilation duct, you just need to turn natural ventilation into forced ventilation. To do this, it is enough to determine the model of the fan and the circuit for connecting it to electricity.
The exception is apartments in which the ventilation shaft is adjacent to only one of the rooms of a separate bathroom - there will need to be a canal
In a private house, you usually have to build a system from scratch, leading the ventilation pipe to the street through the roof, less often through the wall. In this case, it is necessary not only to think over everything, but also to draw up a plan diagram according to which it will be convenient to consider the necessary materials and make installation.
It is worth checking the presence of natural traction in the existing mine, and in case of its complete absence, contact the Housing Department for cleaning. For effective air exchange, it is better to place the hood opposite the door or flow valve, if any.
The next stage is the purchase of everything you need. It is even worth buying in advance that will be installed at the very end of the repair, because another model of the fan may not be connected to the wires already supplied.
Having figured out how to connect the purchased fan and choosing a ventilation scheme, you can proceed to repair the bathroom.
During the decorative decoration of the walls and ceiling, wires are laid in corrugated insulating tubes, if necessary, a ventilation duct is built and the size of the fan hole is adjusted. Connection of wiring and installation of switches is also carried out at this stage.
An alternative option, available only in a private house is the installation of a duct fan. When mounting it, only a special plate is screwed to the wall, and the main body with the motor snaps into the side fasteners
The fan itself is installed after finishing. The installation procedure is as follows:
- Make sure that the wires for the fan are de-energized.
- Remove the front panel, insert the housing into the hole and mark the places for fastening on the tile with a marker.
- Drill holes with a drill with a drill on ceramics, hammer in the dowels. This stage can be neglected completely or only part of the provided fasteners can be used. Plastic fans weigh a little, usually for fixing enough liquid nails or polymer glue.
- Even when attaching to self-tapping screws, the perimeter of the fan housing must be lubricated with silicone or another polymer - to absorb vibrations and prevent noise.
- Insert the housing into the hole, check the level (for models with a square front) and press firmly until the sealant seizes.
- Connect the wires to the terminals of the device and fix so that there are no exposed areas.
- Turn on ventilation, check operation in all provided modes.
- Install the front panel.
This order is universal, suitable for overhead fans of any model. It also does not matter if the fan is installed in the wall or in the ceiling - only the installation of channel models differs.
Some models have a control board with the ability to set the operating mode for the bathroom or toilet, as well as setting a timer
If the fan is designed with a timer, a hygrometer, a mode switch or other equipment, do not forget to set it up until you put on a decorative panel.
Often from the factory, the timer adjustment screw is unscrewed to a minimum - select the necessary duration of work experimentally.
There may also be a mode switch that looks like 3 or 4 metal pins with a removable jumper on two of them.
In the "toilet" mode, the fan starts immediately, at the same time as the light is turned on, and the time set by the timer runs. In the “bathroom” mode, the turn-off signal is a turn-off of the light, so that noise and drafts will not disturb you in the shower.
After adjustment and adjustment, do not forget to close the holes on the cover to protect the board from moisture, if provided for by the design
The built-in hygrometer can be adjusted to a certain level of humidity at which the fan will start.
Common mistakes and additional tips
Errors in connecting the fan can cause not only incorrect operation of the hood, but also a short circuit or fire. Do not forget that the bathroom is a room with high humidity, which means it is especially dangerous for electrical appliances and wiring.
In order to arrange ventilation without errors on the first attempt, consider the following tips:
- The fewer bends and the simpler the design of the ventilation duct, the better the draft.
- With a single ventilation system for a separate bathroom, the air should move from the bath to the toilet, and not vice versa.
- For all wire connections, use terminal blocks rather than electrical tape.
- Strip exactly the part of the wire that goes into the terminal block.
- Check for a mosquito net in the fan. If suddenly it is not there, add it, because mosquitoes and other insects feel great in warm, moist ventilation shafts.
- In a private house, be sure to insulate part of the ventilation duct or mines passing through unheated rooms. Otherwise, in cold weather there will be no traction.
- Do not neglect the grounding for metal fans.
In addition, so that the fan does not interfere with natural ventilation when it is turned off, you can use double rectangular grilles, with a hole for the fan at the top and a regular grille under it.
When connecting the fan power, do not confuse the contacts: N - zero, T or LT - timer, phase from the switch, L or Line - phase directly from the box
If it is not possible to install a double grille, you can preserve natural ventilation by substituting 1–2 cm foam legs under the corners of the case, in places of fastening with screws. As a rule, the ventilation window is square, and the fan casing is round, and these gaps are quite enough for air circulation.
Please note that even an ideally installed and sufficiently powerful fan will not work efficiently if there is not enough supply ventilation. Usually it is provided by a gap of 1.5–2 cm under the door to the bathroom, but for beauty it can be replaced with a special grill that cuts into the bottom of the door.
Also, make sure that fresh air generally enters the housing, because after installing plastic windows and new doors, insulating walls and concrete screed on the floor, the apartment is hermetically sealed like a thermos.
In addition, the exhaust fan may need cleaning. Therefore, we recommend that you also read the step-by-step instructions for disassembling and cleaning the device. More details - follow the link.
Connecting a simple fan is described in detail here:
Summing up, we can say that it’s quite possible to independently equip an effective ventilation system in an apartment, but you need to be careful and think through everything carefully in advance. If you are not confident in your abilities, entrust the matter to a specialist, because errors in working with electrical wiring can lead to sad consequences.
Have you ever installed a fan in a bathroom or toilet? Please tell us which connection scheme did you use and were there any difficulties in installation? Leave your comments, share your experience - the block for communication is located under the article.